Buy 3D printers, filament, parts & tools | lowest prices

Product added to cart. Return Cartridge added product

[Popup will close in 1 sec]

123-3D.ie
U29-30 North Park
Dublin D11 TX88

T: 01 963 7043
E: info@123-3D.ie

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Quantity	Product
No products
Total: €0.00

123-3D black PLA filament

In stock

€19.95

Super Lube

€8.25

3D PRO black pen with LCD display (123-3D version)

€29.50

Modifi3D repair/modification tool

€34.75

RAMPS v1.4 (fully assembled)

Zoom in

Description

RAMPS stands for RepRap Arduino Mega Pololu Shield and contains all the electronics for a complete RepRap printer. All components on RAMPS have been tested for a maximum input voltage of 24V. For proper cooling it is important that the RAMPS board is placed on top of the Arduino stack.

RAMPS has the following properties:

3 MosFets for heater/fan
5 Step Driver Locks
USB type B connector
5A fuse for protection
11A fuse for protection for the heated bed
3 Thermistor connections
Multiple AUX connections available

Specifications

Brand:	123-3D	On-board stepper drivers:	5
No of MOSFETs:	3	Our item no:	DRW00008
No of thermistors:	3

€16.75 (Incl. 23% VAT) (€13.62 Excl. 23% VAT)

EU warehouse

Graphic LCD display 12864 smart controller

Zoom in

Description This graphic LCD display is suitable for Ramps 1.4. and is supplied complete with 30cm ribbon cables and adapter for Ramps 1.4. In addition to a beautiful display with a resolution of 128 x 64 pixels, the LCD also has an SD card slot, buzzer and a push button.

This LCD display is not compatible with the Minitronics, Megatronics and Ultratronics boards.

Specifications

Brand:	123-3D	Operating volt logic:	5V
Cable length:	30 cm	Our item no:	DRW00018
Height:	25 mm	Width:	87 mm
Length :	87 mm

Order now, we can ship this tomorrow!

€29.50 (Incl. 23% VAT) (€23.98 Excl. 23% VAT)

In stock

Arduino Mega 2560 clone (123-3D version)

Zoom in

Description The Arduino MEGA2560 clone is a microcontroller board, based on the ATmega2560. This board has:

54x Digital input/output pins (of which 14 are suitable for PWM outputs)
16x Analog inputs, 4 UARTs (hardware serial ports)
16MHz crystal oscillator
Flash Memory 256KB (8KB already in use by the bootloader)
USB connection
power jack
ICSP header
Reset button

The microcontroller board can be connected via USB, an AC-DC adapter or a battery. This board is compatible with most shields designed for the Arduino, Mega Duemilanove or Diecim. The Arduino Atmega 2560 clone features a CH340G USB-to-Serial chip.

Specifications

Brand:	123-3D	Input voltage limits:	7.12V
DC current for 3.3V pin:	50 ma	Operating volt logic:	5V
DC current per I/O pin:	40 ma	Processor:	ATMEGA 2560
EEPROM:	4KB	Our item no:	DRW00007
Flash memory:	256 KB	SRAM:	8 KB
Input voltage:	7 - 12V recommended

Order now, we can ship this tomorrow!

€29.50 (Incl. 23% VAT) (€23.98 Excl. 23% VAT)

In stock

Arduino Mega 2560 clone micro USB (123-3D version)

Zoom in

Description The Arduino MEGA2560 clone is a microcontroller board, based on the ATmega2560. This board has:

54 x digital input/output pins (of which 14 are suitable for PWM outputs);
16 x analog inputs, 4 UARTs (hardware serial ports)
16MHz crystal oscillator
Flash memory 256kB (8kB already in use by the bootloader)
Micro USB connection
Power jack
ICSP header
Reset button

The microcontroller board can be connected via micro-usb, an AC-DC adapter or a battery. This board is compatible with most shields designed for the Arduino, Mega Duemilanove or Diecim. The Arduino Atmega 2560 clone features a CH340G USB-to-Serial chip.

Specifications

Brand:	123-3D	Input voltage:	7 - 12V recommended
DC current for 3.3V pin:	50 ma	Input voltage limits:	7.12V
DC current per I/O pin:	40 ma	Processor:	ATMEGA 2560
EEPROM:	4KB	Our item no:	DRW00019
Flash memory:	256 KB	SRAM:	8 KB

€29.50 (Incl. 23% VAT) (€23.98 Excl. 23% VAT)

EU warehouse

Arduino Mega 2560 Rev3 (original)

Zoom in

Description The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It features 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a ceramic resonator (16Mhz), a USB connection, a power jack, an ICSP header and a reset button.

The Arduino Mega 2560 Rev3 offers full microcontroller support and is easy to connect with a USB cable, AC-DC adapter or battery and you can start right away! The Mega is compatible with most shields made for the Arduino Uno, the Duemilanove or the Diecimila.

New features of the R3 version are:

ATmega16U2 as USB-to-serial converter instead of the 8U2
1.0 Pinout: Additional SDA and SCL pins, placed near the AREF pin, for TWI communication and two other new pins at the RESET pin: the IOREF that allows shields to adapt to the voltage supplied by the board. The second pin is a disconnected pin, reserved for future use
Stronger circuit breaker

Specifications

Analog input pins:	16	Length :	101 mm
Brand:	Arduino	Operating volt logic:	5V
DC current for 3.3V pin:	50 ma	Processor:	ATMEGA 2560
DC current per I/O pin:	20 ma	Our item no:	DAR00003
EEPROM:	4KB	SRAM:	8 KB
Flash memory:	256 KB	Weight:	0.037 kg
Input voltage:	7 - 12V recommended	Width:	53 mm

Order now, we can ship this tomorrow!

€67.50 (Incl. 23% VAT) (€54.88 Excl. 23% VAT)

In stock

Graphic LCD Display 12864 v1.0 for RepRap printers

Zoom in

Description This graphic LCD screen allows you to quickly and easily add a display to your RepRap 3D printer.

The display has a resolution of 128 x 64 pixels, has an SD card slot and is equipped with a push button. The LCD screen is compatible with Minitronics, Megatronics, Ultratronics and RAMPS and has different connection headers. The display functions via SPI and the buttons are connected to digital IOs.

NOTE: Cabling is not included.

Data sheet (PDF)
Test firmware (zip)
Minitronics firmware (zip)
Megatronics firmware (zip)
RAMPS firmware (zip)
Not compatible with the Megatronics 3.2

Specifications

Brand:	RepRapWorld	Operating volt logic:	5V
Dimensions:	25 x 90 x 94 mm	Our item no:	DRW00015

€47.50 (Incl. 23% VAT) (€38.62 Excl. 23% VAT)

EU warehouse

Header for on RAMPS board (24 way)

Zoom in

Description This black header from 123-3D has 24 pins. It is suitable for the Pololu stepper motor control on a RAMPS board.

Specifications

Brand:	123-3D	Our item no:	DAR00104
Colour:	black

Order now, we can ship this tomorrow!

€1.75 (Incl. 23% VAT) (€1.42 Excl. 23% VAT)

In stock

Header for on RAMPS/GEN7 board (8 way)

Zoom in

Description This black header from 123-3D has 8 pins. It is suitable for the Pololu stepper motor control on a RAMPS/GEN7 board.

Specifications

Brand:	123-3D	Our item no:	DAR00105
Colour:	black

Order now, we can ship this tomorrow!

€0.95 (Incl. 23% VAT) (€0.77 Excl. 23% VAT)

In stock

Screw terminal header (2 way)

Zoom in

Description This simple screw terminal is ideal for RAMPS boards, as well as DIY electronics projects. The screw contact has 2 connections. By linking several screw headers together, you can create a long row.

Specifications

Brand:	123-3D	Our item no:	DAR00139
Colour:	blue

Order now, we can ship this tomorrow!

€1.10 (Incl. 23% VAT) (€0.89 Excl. 23% VAT)

In stock

Screw terminal header (3 way)

Zoom in

Description This simple screw terminal is ideal for RAMPS boards, as well as DIY electronics projects. The screw contact has 3 connections. By linking several screw headers together, you can create a long row.

Specifications

Brand:	123-3D	Our item no:	DAR00140
Dimensions:	9.7 x 15.4 x 7.6 mm

Order now, we can ship this tomorrow!

€1.10 (Incl. 23% VAT) (€0.89 Excl. 23% VAT)

In stock

Jumpers (15-pack)

Zoom in

Description These black jumpers are suitable for various electronics boards such as the Arduino boards, RAMPS and CNC shield. This pack contains 15 jumpers.

Specifications

Brand:	123-3D	Our item no:	DAR00006
Pin pitch:	2.54 mm

Order now, we can ship this tomorrow!

€2.50 (Incl. 23% VAT) (€2.03 Excl. 23% VAT)

In stock

External MOSFET module, 25A (123-3D version)

Zoom in

Description This powerful MOSFET module (type NCEP01T18T) withstands higher currents than the MOSFET on your RAMPS or similar electronics boards. The module is suitable for 12V and 24V heated beds or hot ends and can handle PWM controls. The kit includes a ready-to-install PCB with a short connection cable.

NOTE: For high currents it is important to actively cool the module. The maximum current without active cooling is ±18A.

Specifications

Brand:	123-3D	Our item no:	DHB00017
Height:	33 mm	Voltage rating:	24 v
Length :	60 mm	Width:	50 mm
Max current:	25 A

Order now, we can ship this tomorrow!

€16.75 (Incl. 23% VAT) (€13.62 Excl. 23% VAT)

In stock

Menu

My 123-3D.ie

Customer reviews

Payment options

Follow us on social media

Official dealer

Shopping cart

Don't forget the.....!

Popular products

RAMPS

Menu

Search product

My 123-3D.ie

Customer reviews

Payment options

Follow us on social media

Official dealer

Shopping cart

Don't forget the.....!

Newsletter

Popular products

RAMPS