The filament does not stick to the print bed

123-3D.ie
U29-30 North Park
Dublin D11 TX88

T: 01 963 7043
E: info@123-3D.ie

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Quantity	Product
No products
Total: €0.00 (Incl. 0% VAT)

3DLAC adhesive spray, 400ml

In stock €12.75

Home
The filament does not stick to the print bed

3D PRINTING HELP CENTRE

In the 123-3D help centre, we answer all your questions about 3D software and printer settings, problems you may experience during or after 3D printing and other 3D-related topics.

The filament does not stick to the print bed

To ensure that the object can be printed properly, it is important that the first layer is firmly attached to the surface (bed) of the printer. If not, problems will arise later. Filament not sticking can have various causes. Below you will find the most common causes and the corresponding solution.

The bed is not flat

Because many printers have an adjustable bed that is controlled by multiple screws or knobs, the print bed may not be flat/level. If the first layer of the print does not stick well, first check whether there is something wrong with it. Creating a perfect first layer is only possible if the bed is completely level.

The nozzle starts too far away from the print surface

If the nozzle starts printing too far from the surface, the filament will not be pressed against the bed. You can easily solve this problem by raising the bed manually or by using G-Code offsets in your 3D printer software. These offsets allow you to fine-tune the Z-axis without having to change the hardware. Be careful when making adjustments. Because a layer of the print is often only 0.2mm thick, a small adjustment can make a big difference.

The first layer is printed too fast

It is important that the first layer of filament can adhere well to the print bed before you start on the next layer. Therefore, it may be useful to print the first layer at a lower speed. Often the printer software has a special function for this. You can then set this so that the first layer is printed, for example, 40% slower than the rest of the object.

Temperature settings

As filament cools from a warm temperature to a cooler temperature, it tends to shrink. The print bed does not "shrink" and this can cause the first layer to come off. If the first layer adheres well, but does come off later, this may be due to the temperature settings. To prevent this, a heated bed is often used with materials that require a high temperature for printing, such as ABS. This heated print bed ensures that the temperature remains constant and that the first layer does not shrink and therefore come off. When choosing the temperature, you can assume that the ideal temperature for PLA is 60-70 degrees. For ABS this is 100-120 degrees. In your printer software, use the "Temperature" tab to set this.

Do you use a cooling fan? Then try turning these off for the first few layers, so that these layers don't cool down too quickly. You can also use the printer software for this, specifically the "Cooling" tab. Set two set points here: at layer 1, the fan speed must be 0%, from layer 5, for example, it can be 100% again.

The surface of the print bed

Before printing, check whether the surface is clean and to be on the safe side, run some water or alcohol over the print bed. Some 3D printers have a print bed made of material that allows specific types of filament to adhere well, such as a BuildTak layer for PLA or a special type of glass for ABS. If this is not the case with your 3D printer, there are many options to ensure that the filament adheres well to the print bed. PLA, for example, stays in place when using painter's tape and for ABS you can use Kapton tape. A temporary adhesive spray such as 3DLAC's adhesive spray also provides excellent bed adhesion.

Back to the 3D printing help centre

Back to all 3D printing problem FAQs

Menu

My 123-3D.ie

Customer reviews

Payment options

Follow us on social media

Official dealer

Shopping cart

Don't forget the.....!

The filament does not stick to the print bed

3D PRINTING HELP CENTRE

The filament does not stick to the print bed

The bed is not flat

The nozzle starts too far away from the print surface

The first layer is printed too fast

Temperature settings

The surface of the print bed

May also be helpful:

Menu

Search product

My 123-3D.ie

Customer reviews

Payment options

Follow us on social media

Official dealer

Shopping cart

Don't forget the.....!

Newsletter

The filament does not stick to the print bed

3D PRINTING HELP CENTRE

The filament does not stick to the print bed

The bed is not flat

The nozzle starts too far away from the print surface

The first layer is printed too fast

Temperature settings

The surface of the print bed

May also be helpful: